Home > Scale Rock Crawlers > Scale Model Specific Aftermarket Parts > Axial SCX10 Wrangler Rubicon Honcho Dingo AX10 >

GCM Axial SCX-10 Front Motor Mount with Hex Hardware BLACK GR0195
GCM Axial SCX-10 Front Motor Mount with Hex Hardware BLACK GR0195


 
Alternative Views:


List Price: $32.00
TCS Price: $27.99

Stock Status: In Stock


Product Code:
SKU186654

Qty:

Description
 

The SCX10 Front Motor Mount will allow you to easily mount your motor and Axial stock transmission, OR the RC4WD AX2 transmission, on the nose of the SCX10 frame, and make tons of room in the center for a Transfer Case and Interior for your custom build.

This process listed below WILL move your body posts OUTward from the center by about 12mm on each side, though. If you are in the middle of building a truck, and don't have mount holes in the body, this is no problem, but if you are re-using an existing body, you will need new body post holes to make this work. It also requires a frame mounted servo, available also at GCM, and removal of the axle mounted servo bracket.

Step 1: Remove shocks, and then Remove the shock towers, and take the left one, mounted the SAME WAY, but on the right side. Take the right side one, keeping the FWD leg to the front, and mount it on the left side. That's it.

Step 2: Re-install shocks into the REARward mount holes.

Step 3: Assemble the motor/trans on the new mount plate using the NEW plate as a replacement for the axial motor mount plate. That's it. Take off the stock plate, mount up the new plate, done.

Step 4: Slide the new mount, with trans and motor etc installed, right into the position as shown below, and insert the 4 new mount screws (provided) through the top tower at the FWD shock position and the lower front shock tower screw hole. DONE.
Optional parts required for #6 and #7 below:

Step 6: Install your favorite GCM Transfer case in place of the stock center trans. It will directly fit to the 2 outside mount holes in the skidplate.

Step 7: re-install your center FWD and Rear driveshafts on the T-Case, and then add one more same length shaft to the T-Case up to the trans at the front.

Comes with all hex hardware and ONE front motor mount finished in BLACK.

NOTES:
1: When using the RC4WD AX2 transmission and GCM Mount, you must remove the servo bracket from the transmission and relocate to a custom location on your truck. A longer linkage will be required.


Average Rating: 5 of 5 Total Reviews: 5 Write a review »

  0 of 0 people found the following review helpful:
 
Just a rookie, my experience may differ from yours May 30, 2017
Reviewer: Chris from North pole, AK United States  
Very nice kit, only concern is when you tighten your trans to motor plate you can squeeze the trans case making case super tight and outputs are hard to spin. Threadlock and a snug tighten should do the trick.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Front motor mount GCM May 27, 2017
Reviewer: chris dowty from monticello, IN United States  
Great product as usual. Game me the room to add my gear reduction unit.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
GCM Axial SCX-10 Front Motor Mount May 8, 2016
Reviewer: Anonymous Person from Denver, CO United States  
I was impressed with the quality of this mount. It made it possible to move the motor and transfer case to the front.  Now  I can mount the hard body I have and not have to cut it up the floor board to fit.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great motor mount January 15, 2016
Reviewer: Andy Scott from Loganville, GA United States  
Fits great and moves the transmission and motor to the front of the chassis between the shock towers. Doesn't come with instructions but it's pretty much self explainitory. Fast shipping and great price from TCS as always.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great Mount November 17, 2014
Reviewer: Spork_Assassin from Saranac, MI United States  
Strong, well made, excellent finish work.  Not much more to say about a mount

Was this review helpful to you?